< ResourcesIndustry: Steelmaking

Dummy bar head repair for continuous casting

Key facts
  • Part: Slab caster dummy bar head, about 1.8 tonnes
  • Damage: Eroded hook edges, heat cracks on the top face, worn side faces
  • Rebuilt: Around 20 kg of heat-resistant steel, in one standard setup
  • Result: 60% faster repair, 42% less material, 20% longer service life

Rebuilding a slab caster dummy bar head after repeated contact with liquid steel, without reprogramming the robot by hand.

Every cast sequence on a continuous caster starts with the dummy bar. Its head plugs the bottom of the mould, the first steel solidifies around it, and it pulls the new strand out through the machine. A replacement head is expensive, has a long lead time, and a damaged one puts the whole caster at risk of a failed start.

This case shows how MaxQ Repair restores a 1.8-tonne slab dummy bar head to its original geometry, so it goes back into service instead of onto the scrap pile.

Watch the repairBook a demo
Worn slab caster dummy bar head on a pallet before repair

The challenge

Repairing a dummy bar head is a demanding maintenance job:

  • Harsh, uneven damage: Each start exposes the head to liquid steel, thermal shock and the mechanical load of strand disconnection. The result is eroded hook edges, heat cracks on the top face and worn side faces.
  • Large component, tight tolerances: The head is about 1.8 tonnes and must fit the mould cross-section precisely to seal the mould and start the cast safely.
  • Two wear depths in one part: The hook and top face are cracked and eroded deep and need gouging. A fixed weld program cannot handle both without manual adjustment.
  • Manual welding does not scale: Building up roughly 20 kg of weld metal by hand takes days of skilled work, and crack resistance varies from welder to welder.
Render of a dummy bar head with the gouged repair zone along the hook rebuilt by MaxQ Repair

The solution

MaxQ Repair turns the repair into a scan-plan-repair routine, driven by the actual worn geometry of the head:

  • Gouge to a clean base: Cracked and eroded zones on the hook and top face are gouged out to a clean base.
  • Scan the head as it is: The 3D camera captures the gouged surface, so the system works from the real geometry, distortion included.
  • Automatic toolpaths: MaxQ Repair software generates the weld paths straight from the scan and deposits heat-resistant steel only where material is missing.
  • Full reach, no special tooling: Every gouged area is reachable in one standard setup, so the whole repair runs without repositioning.
Slab caster dummy bar head after automated repair with MaxQ Repair

The result

The dummy bar head is rebuilt in one automated process and can be machined back to its original dimensions:

 

  • 60% faster repair, 42% less material use, 20% longer service life
  • Minimized pre-processing: The system identifies the damage and repairs it to the required extent without extensive pre-weld machining.
  • No offline programming: Toolpaths come from the scan, so a different damage pattern next time needs no new program.
  • Consistent, traceable quality: Current, voltage and interpass temperature are monitored throughout, and every repair is logged automatically.
Steel plant hall with glowing ladles of liquid steel and an overhead crane hook

Conclusion

A dummy bar head is too critical to scrap after a few hundred starts. MaxQ Repair lets steel plants rebuild a worn 1.8-tonne head in a single automated cycle and return it to the caster with its original geometry restored.

Contact us to learn more or discuss your specific application.

Book a demo

Watch the repair

How to repair your part with MaxQ

About MaxQ Repair

MaxQ Repair is an all-in-one automated solution for the repair of metal parts, such as rails, rotors, and dies, that are subject to wear in service.

Book a demo

Leave your details to book a 30 minute demo

In an online call of 30 minutes, we will show you the functionality and practical applications of MaxQ Repair